Skip to Main Content
 

Global Search Box

 
 
 

ETD Abstract Container

Abstract Header

Evaluation of Thermal Stress in Carbon/Glass Hybrid and Glass Nanocomposite under Resistive Heating

Gnanasekar, Vignesh Kumar
http://orcid.org/0000-0002-5216-9460
http://rave.ohiolink.edu/etdc/view?acc_num=dayton1450037103

Abstract Details

2015, Master of Science (M.S.), University of Dayton, Civil Engineering.
Resistive heating of nanocomposite material is proposed for use in many applications because of its light weight and low current requirements. When the nanocomposites are resistively heated, thermal stresses starts arising in it due to mismatch of CTE between the fiber and matrix of the nanocomposite. A nanocomposite material can withstand only limited thermal stress when it is resistively heated. If the thermal load is too high, or combined with other external loads, the nanocomposite can fail by means of delamination, crack formation, warpage and other related modes. Hence, studying the thermal stress that develops in nanocomposites upon resistive heating will help in preventing otherwise unanticipated failures. The objective of this effort was to develop and experimentally validate a Finite Element Method model for evaluation of the thermal stress arising in nanocomposite material upon resistive heating. In order to fill the technology gap of predicting thermal stress in resistively heated nanofiber composites, a finite element method (FEM) model was created. This model was created using ABAQUS® software. To verify the results of the model, the experimental method of hole-drilling was adopted. The nanocomposite considered for the research were a carbon/glass hybrid with epoxy resin and a glass/epoxy composite reinforced with CNT Buckypaper. The experiment was based on the principle of redistribution of stress when the hole is drilled in the composite and the relieved strain is measured by a strain gage rosette. The strain release corresponds to the thermal stress that was present before the drilling the hole. The thermal stress results of hole-drilling method were compared with the FEM model result, validating the model and analysis results. The verified FEM model can be used to predict thermal stresses arising in nanocomposites and preventing failure when the nanocomposite is resistive heated and externally loaded.
Thomas Whitney (Advisor)
77 p.
Aerospace Materials; Automotive Materials; Civil Engineering; Engineering; Materials Science; Nanotechnology
CNT bucky paper; resistive heating; nanocomposites; hole drilling method; thermal stress measurement; resistive heating deicing; finite element method

Recommended Citations

Citations

  • Gnanasekar, V. K. (2015). Evaluation of Thermal Stress in Carbon/Glass Hybrid and Glass Nanocomposite under Resistive Heating [Master's thesis, University of Dayton]. OhioLINK Electronic Theses and Dissertations Center. http://rave.ohiolink.edu/etdc/view?acc_num=dayton1450037103

    APA Style (7th edition)

  • Gnanasekar, Vignesh Kumar. Evaluation of Thermal Stress in Carbon/Glass Hybrid and Glass Nanocomposite under Resistive Heating. 2015. University of Dayton, Master's thesis. OhioLINK Electronic Theses and Dissertations Center, http://rave.ohiolink.edu/etdc/view?acc_num=dayton1450037103.

    MLA Style (8th edition)

  • Gnanasekar, Vignesh Kumar. "Evaluation of Thermal Stress in Carbon/Glass Hybrid and Glass Nanocomposite under Resistive Heating." Master's thesis, University of Dayton, 2015. http://rave.ohiolink.edu/etdc/view?acc_num=dayton1450037103

    Chicago Manual of Style (17th edition)

dayton1450037103
1,288
© 2015, some rights reserved.Creative Commons License Evaluation of Thermal Stress in Carbon/Glass Hybrid and Glass Nanocomposite under Resistive Heating by Vignesh Kumar Gnanasekar is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License. Based on a work at etd.ohiolink.edu.
This open access ETD is published by University of Dayton and OhioLINK.