Skip to Main Content
 

Global Search Box

 
 
 
 

Files

File List


ucin997987327.pdf (2.56 MB)

ETD Abstract Container

Abstract Header

Novel MEMS Pressure and Temperature Sensors Fabricated on Optical Fibers

Abeysinghe, Don Chandana
http://rave.ohiolink.edu/etdc/view?acc_num=ucin997987327

Abstract Details

2001, PhD, University of Cincinnati, Arts and Sciences : Physics.
This thesis presents the design, fabrication, and testing of novel MEMS pressure and temperature sensors fabricated on optical fiber end faces. A simple micromachining process compatible with MEMS was developed in fabricating sensors directly on optical fibers. The pressure sensor configuration involves anodic bonding of a piece of an extremely thin silicon wafer onto the fiber end face over a cavity etched in the central portion of the fiber end face. Final device diameter is thus the same as that of the optical fiber. The temperature sensor is based on anodically bonding a thin piece of silicon onto the fiber end face.The pressure sensors were fabricated on 400 um diameter fibers while temperature sensors were fabricated on both 200 and 400 um diameter fibers. Pressure measurements were made over the 14 to 80 psi range while temperature measurements were made over the 23 to 300 Celcius range. Pressure sensor sensitivities of 0.1 mV/psi and 0.2 mV/psi were obtained. The pressure sensors were designed with cavity diameter d=150 um, and cavity depth h=0.640 um. Diaphragm thickness for the two sensors were t=7.1, and t=3.4 um. Higher sensitivity was achieved by design of a sensor with the thinner diaphragm. A sensor array fabrication effort demonstrated that our micromachining process could be extended to simultaneous processing of an array of fibers. The temperature sensor was fabricated by bonding 3.1 um thick silicon onto the fiber end face. An oxidant-resistant encapsulation scheme for the temperature sensor was proposed, namely aluminum coated silicon nitride (Al/Si3N4). The uncoated side of silicon was bonded to a fiber end face using the anodic bonding method. The measured values of kf=(lambda)-1x(dlambda/dT) for capped and uncapped sensors were kf=(7.5±0.6)x10-5/Celcius, and kf=(7.2±0.1)x10-5/Celcius respectively. The measured kf value for the uncapped sensor is equal to that which was determined using the published material properties for crystalline silicon (kf=7.9x10-5/Celcius) within measurement uncertainty. The micromachining process developed for micromachining fiber end faces along with the bonding of silicon to fiber end faces can be extended to fabrication of other MEMS based micro-optic devices where fiber optic interrogation is advantageous.
Howard Jackson (Advisor)
PRESSURE SENSOR; TEMPERATURE; MEMS; FIBER OPTIC SENSOR; FABRY-PEROT SENSOR

Recommended Citations

Citations

  • Abeysinghe, D. C. (2001). Novel MEMS Pressure and Temperature Sensors Fabricated on Optical Fibers [Doctoral dissertation, University of Cincinnati]. OhioLINK Electronic Theses and Dissertations Center. http://rave.ohiolink.edu/etdc/view?acc_num=ucin997987327

    APA Style (7th edition)

  • Abeysinghe, Don. Novel MEMS Pressure and Temperature Sensors Fabricated on Optical Fibers. 2001. University of Cincinnati, Doctoral dissertation. OhioLINK Electronic Theses and Dissertations Center, http://rave.ohiolink.edu/etdc/view?acc_num=ucin997987327.

    MLA Style (8th edition)

  • Abeysinghe, Don. "Novel MEMS Pressure and Temperature Sensors Fabricated on Optical Fibers." Doctoral dissertation, University of Cincinnati, 2001. http://rave.ohiolink.edu/etdc/view?acc_num=ucin997987327

    Chicago Manual of Style (17th edition)

ucin997987327
4,336
© 2001, all rights reserved.
This open access ETD is published by University of Cincinnati and OhioLINK.