Skip to Main Content
 

Global Search Box

 
 
 
 

Files

File List


NorfamilaCheMatDissertation2016.pdf (4.38 MB)

ETD Abstract Container

Abstract Header

Membrane Process Design for Post-Combustion Carbon Dioxide Capture

CHE MAT, NORFAMILA BINTI
http://rave.ohiolink.edu/etdc/view?acc_num=toledo1474118357472385

Abstract Details

2016, Doctor of Philosophy, University of Toledo, Chemical Engineering.
Concerns over the effects of anthropogenic carbon dioxide (CO2) emissions from fossil-fuel electric power plants has led to significant efforts in the development of processes for CO2 capture from flue gas. Options under consideration include absorption, adsorption, membrane, and hybrid processes. The US Department of Energy (DOE) has set goals of 90% CO2 capture at 95% purity followed by compression to 140 bar for transport and storage. Ideally, the Levelized Cost of Electricity (LCOE) would increase by no more than 35%. Because of the relatively low CO2 concentration in post-combustion flue gas, most of the reported process configurations for membrane systems have sought to generate affordable CO2 partial pressure driving forces for permeation. Membrane Technology and Research, Inc. (MTR) proposed the use of an air feed sweep system to increase the CO2 concentration in flue gas. This process utilizes a two-stage membrane process in which the feed air to the furnace sweeps the flue gas in the second stage to reduce the flow of CO2 in the effluent to 10% of that leaving the furnace. Such a design significantly reduces capture costs but leads to a detrimental reduction in the oxygen concentration of the feed air to the boiler. In this dissertation, the economic viability of combined cryogenic-membrane separation is evaluated. The work incorporates the tradeoff between CO2/N2 selectivity and CO2 permeability that exists when considering the broad range of potential membrane materials. Of particular interest is the use of lower selectivity, higher permeability materials such as polydimethylsiloxane (PDMS). Additional enriching stages are required in a membrane-cryogenic air feed sweep configuration to enable use of these materials and achieve the 90% CO2 recovery and 95% purity targets. The higher CO2 permeance of PDMS significantly reduces the total module membrane area requirement and associated capital cost (CAPEX). However, the lower selectivity increases the parasitic plant load required to produce the desired CO2 purity due the need for an additional membrane stage and the associated recycle loops; this increases operating cost (OPEX). Multistage membrane-cryogenic air feed sweep configurations are optimized using the Robeson upper bound relation to relate membrane permeability to selectivity. Membrane selectivity is varied over a broad range encompassing the values considered by MTR. Permeability is varied with selectivity according to the variation anticipated by the upper bound of the Robeson plot for CO2 and N2. Membrane permeance is calculated assuming membranes can be fabricated with an effective thickness of 0.1 micron. Additionally, the two stages may utilize different membrane materials. The feed and permeate pressures also are varied over ranges encompassing the values proposed by MTR. The optimization space of membrane properties and operating conditions is scanned globally to determine the process design that minimizes LCOE. The oxygen concentration to the boiler is evaluated during the optimization process and can be used to constrain viable alternatives. The results indicate a fairly broad range of membrane properties can yield comparable LCOE near the minimum. The optimal operating pressure range is somewhat narrower. The minimum allowable oxygen concentration can constrain viable designs significantly and is critical to process economics. Membrane separation system shows a rapid response as the incoming flow flue gas flow rate changes due to the small time constant value. High pressure ratio and low CO2/N2 shows the fastest response due to the smaller residence time. Considering the fixed membrane area, compressor and vacuum power, step changes of incoming flue gas flow rate results in the variation effect of feed compression pressure and also vacuum permeate pressure. This leads to selectivity dependent changes in permeate flow that affect CO2 recovery.
GLENN LIPSCOMB, PhD (Committee Chair)
MARIA COLEMAN, PhD (Committee Member)
YAKOV LAPITSKY, PhD (Committee Member)
CONSTANCE SCHALL, PhD (Committee Member)
MATTHEW FRANCHETTI, PhD (Committee Member)
190 p.
Chemical Engineering
Hollow fiber membrane, Post-combustion carbon capture, carbon dioxide, membrane gas separations

Recommended Citations

Citations

  • CHE MAT, N. B. (2016). Membrane Process Design for Post-Combustion Carbon Dioxide Capture [Doctoral dissertation, University of Toledo]. OhioLINK Electronic Theses and Dissertations Center. http://rave.ohiolink.edu/etdc/view?acc_num=toledo1474118357472385

    APA Style (7th edition)

  • CHE MAT, NORFAMILA. Membrane Process Design for Post-Combustion Carbon Dioxide Capture . 2016. University of Toledo, Doctoral dissertation. OhioLINK Electronic Theses and Dissertations Center, http://rave.ohiolink.edu/etdc/view?acc_num=toledo1474118357472385.

    MLA Style (8th edition)

  • CHE MAT, NORFAMILA. "Membrane Process Design for Post-Combustion Carbon Dioxide Capture ." Doctoral dissertation, University of Toledo, 2016. http://rave.ohiolink.edu/etdc/view?acc_num=toledo1474118357472385

    Chicago Manual of Style (17th edition)

toledo1474118357472385
1,475
© 2016, all rights reserved.
This open access ETD is published by University of Toledo and OhioLINK.